Plant 3 adds about 19,000 m² of converting space and a 55.8-tonne Göpfert G-CUT die-cutter. Earlier investment estimates exceeded the €45 million reported at opening.

Straub-Verpackungen has opened its €45 million Plant 3 in Bräunlingen, Germany, as corrugated board sales among members of the German industry association VDW fell 0.1% in 2025. The new hall began printing packaging and preparing orders for shipment in June 2026, before its official inauguration in October.
The expansion adds about 19,000 m² of converting space, a Göpfert G-CUT 13/21 flatbed die-cutter weighing 55.8 tonnes and new material-handling equipment. Straub’s commercial managing director, Dr. Steffen P. Würth, also chairs the VDW. In a September interview, he described the company’s weakest figures in roughly 30 years, without specifying whether the comparison concerned revenue, profit or production volume.
An investment made against a stagnant market
The VDW’s members sold approximately 7.403 billion m² of corrugated board in 2025. Their revenue increased 1.0%, but the association said higher paper costs absorbed the gain. Its weighted containerboard price measure climbed 12.9% in the first half of 2025 and averaged 4.2% above 2024 for the year. The VDW represents companies responsible for roughly 80% of German corrugated production; these are member statistics, not an independent audit of every producer or a measure of Straub’s own financial results.
The project’s price tag also needs context. At the December 2023 groundbreaking, SÜDKURIER reported an estimated €40–50 million before machinery costs. An October 2025 factory report by aktiv quoted Würth describing an investment of more than €50 million. Opening coverage in October 2026 cited €45 million. No comparable final cost breakdown has been published, so the different figures cannot be reconciled reliably or treated as separate investments.
The industrial argument for building was made before the opening. Visiting the older factory in 2025, aktiv found printing, die-cutting and folding-gluing machines crowded into the hall. Würth said Straub wanted to “streamline workflows and spread out production” (translated from German). In the same interview he explained that some machinery would move from Bräunlingen and Blumberg to the new building. That distinction matters: a larger factory does not necessarily add an equivalent amount of net production capacity.
Inside Plant 3: where automation should make the difference
Straub describes roughly 19,000 m² of expanded production and converting space; SÜDKURIER reports approximately 24,000 m² of total usable building area. The figures refer to different measures, not two competing estimates of factory output. The hall also has a green roof and photovoltaic equipment. Neither the electricity generated nor its impact on production costs has been disclosed.
The most visible new machine is a Göpfert G-CUT 13/21 flatbed die-cutter. Straub’s own installation footage identifies a G-CUT weighing 55.8 tonnes, and industry coverage specifies the 13-21 model. It cuts and creases corrugated sheets into box blanks; the downstream steps can include folding, gluing, packing and palletising. Straub has not published a complete equipment list for Plant 3.
Göpfert’s specifications for the G-CUT 13/21 list sheets up to 2,100 × 1,300 mm, a rated mechanical speed of up to 6,500 sheets per hour and maximum cutting force of 500 tonnes. Those figures describe the machine model, not actual running speed at Straub. On short or changing orders, the economic result depends on job preparation, changeovers and the next operation accepting the output without delay.
Straub has shown conveyor installation, while SÜDKURIER describes shuttle systems carrying corrugated material between work areas. Together, these point to a factory designed around material flow. The exact integration of all machines, the labour requirement and any measured reduction in handling time have not been made public.
This is important for converters handling many box sizes. A waiting pallet, an unavailable operator or a queue before folding-gluing can cancel out a die-cutter’s speed advantage. The benefit of automation must therefore be tested at the completed-box stage, rather than inferred from the speed printed in an equipment catalogue.
Consider a purely illustrative case: if a production route spends 20 minutes of each hour waiting for material, cutting that delay to 10 minutes raises potential working time from 40 to 50 minutes — a 25% increase. It does not prove 25% more boxes will leave the plant: printing, finishing, quality and customer demand may still limit shipments. For Straub, the missing evidence is actual changeover time, waiting time between operations, acceptable output per paid labour hour and waste or rework.

A long-term manufacturing bet, not a market forecast
Straub’s investment programme predates today’s weak market. It established a digital-printing and converting site in 2018, opened a logistics centre in 2020 and expanded Plant I in 2022. In the 2025 aktiv interview, Würth explained why another investment followed: “We are investing here for the next generation” (translated from German). The aim was to make room for a more efficient production structure and support the family business over the long term.
The company’s operating network gives the investment a wider significance. Straub processes corrugated packaging around Bräunlingen and Blumberg, while the wider group includes Papierfabrik Vreden, a source of recycled-fibre containerboard. The new plant may change how work is distributed across these operations, although the company has not reported the resulting savings or net capacity increase.
Other European converters are also investing, but in different ways. In January 2025, Austria’s Rondo Ganahl commissioned a €16.5 million BHS Corrugated corrugator at Frastanz, saying it raised the site’s boardmaking capacity by around 10%. In June 2026, Mondi reported improvements at Greven and Ebersdorf in Germany, including automation and pallet-free handling, without disclosing a project budget. Rondo invested in corrugating capacity; Mondi upgraded existing sites; Straub has reorganised and expanded converting space. Their budgets cannot be treated as like-for-like productivity comparisons.
The practical question now is how much of Plant 3’s output will be additional production rather
Straub-Verpackungen has opened its €45 million Plant 3 in Bräunlingen, Germany, as corrugated board sales among members of the German industry association VDW fell 0.1% in 2025. The new hall began printing packaging and preparing orders for shipment in June 2026, before its official inauguration in October.
The expansion adds about 19,000 m² of converting space, a Göpfert G-CUT 13/21 flatbed die-cutter weighing 55.8 tonnes and new material-handling equipment. Straub’s commercial managing director, Dr. Steffen P. Würth, also chairs the VDW. In a September interview, he described the company’s weakest figures in roughly 30 years, without specifying whether the comparison concerned revenue, profit or production volume.
An investment made against a stagnant market
The VDW’s members sold approximately 7.403 billion m² of corrugated board in 2025. Their revenue increased 1.0%, but the association said higher paper costs absorbed the gain. Its weighted containerboard price measure climbed 12.9% in the first half of 2025 and averaged 4.2% above 2024 for the year. The VDW represents companies responsible for roughly 80% of German corrugated production; these are member statistics, not an independent audit of every producer or a measure of Straub’s own financial results.
The project’s price tag also needs context. At the December 2023 groundbreaking, SÜDKURIER reported an estimated €40–50 million before machinery costs. An October 2025 factory report by aktiv quoted Würth describing an investment of more than €50 million. Opening coverage in October 2026 cited €45 million. No comparable final cost breakdown has been published, so the different figures cannot be reconciled reliably or treated as separate investments.
The industrial argument for building was made before the opening. Visiting the older factory in 2025, aktiv found printing, die-cutting and folding-gluing machines crowded into the hall. Würth said Straub wanted to “streamline workflows and spread out production” (translated from German). In the same interview he explained that some machinery would move from Bräunlingen and Blumberg to the new building. That distinction matters: a larger factory does not necessarily add an equivalent amount of net production capacity.
Inside Plant 3: where automation should make the difference
Straub describes roughly 19,000 m² of expanded production and converting space; SÜDKURIER reports approximately 24,000 m² of total usable building area. The figures refer to different measures, not two competing estimates of factory output. The hall also has a green roof and photovoltaic equipment. Neither the electricity generated nor its impact on production costs has been disclosed.
The most visible new machine is a Göpfert G-CUT 13/21 flatbed die-cutter. Straub’s own installation footage identifies a G-CUT weighing 55.8 tonnes, and industry coverage specifies the 13-21 model. It cuts and creases corrugated sheets into box blanks; the downstream steps can include folding, gluing, packing and palletising. Straub has not published a complete equipment list for Plant 3.
Göpfert’s specifications for the G-CUT 13/21 list sheets up to 2,100 × 1,300 mm, a rated mechanical speed of up to 6,500 sheets per hour and maximum cutting force of 500 tonnes. Those figures describe the machine model, not actual running speed at Straub. On short or changing orders, the economic result depends on job preparation, changeovers and the next operation accepting the output without delay.
Straub has shown conveyor installation, while SÜDKURIER describes shuttle systems carrying corrugated material between work areas. Together, these point to a factory designed around material flow. The exact integration of all machines, the labour requirement and any measured reduction in handling time have not been made public.
This is important for converters handling many box sizes. A waiting pallet, an unavailable operator or a queue before folding-gluing can cancel out a die-cutter’s speed advantage. The benefit of automation must therefore be tested at the completed-box stage, rather than inferred from the speed printed in an equipment catalogue.
Consider a purely illustrative case: if a production route spends 20 minutes of each hour waiting for material, cutting that delay to 10 minutes raises potential working time from 40 to 50 minutes — a 25% increase. It does not prove 25% more boxes will leave the plant: printing, finishing, quality and customer demand may still limit shipments. For Straub, the missing evidence is actual changeover time, waiting time between operations, acceptable output per paid labour hour and waste or rework.

A long-term manufacturing bet, not a market forecast
Straub’s investment programme predates today’s weak market. It established a digital-printing and converting site in 2018, opened a logistics centre in 2020 and expanded Plant I in 2022. In the 2025 aktiv interview, Würth explained why another investment followed: “We are investing here for the next generation” (translated from German). The aim was to make room for a more efficient production structure and support the family business over the long term.
The company’s operating network gives the investment a wider significance. Straub processes corrugated packaging around Bräunlingen and Blumberg, while the wider group includes Papierfabrik Vreden, a source of recycled-fibre containerboard. The new plant may change how work is distributed across these operations, although the company has not reported the resulting savings or net capacity increase.
Other European converters are also investing, but in different ways. In January 2025, Austria’s Rondo Ganahl commissioned a €16.5 million BHS Corrugated corrugator at Frastanz, saying it raised the site’s boardmaking capacity by around 10%. In June 2026, Mondi reported improvements at Greven and Ebersdorf in Germany, including automation and pallet-free handling, without disclosing a project budget. Rondo invested in corrugating capacity; Mondi upgraded existing sites; Straub has reorganised and expanded converting space. Their budgets cannot be treated as like-for-like productivity comparisons.
The practical question now is how much of Plant 3’s output will be additional production rather than work transferred from older Straub facilities. The company has not published the site’s annual output, net employment changes or investment payback. Without those figures, the size of the new building cannot tell us how much productive capacity the business has gained.
A clearer picture would come from operating data: shorter changeovers and material-transfer delays, more saleable boxes per paid labour hour, and lower waste or rework. Straub has not yet disclosed these results for the new plant.
While Germany’s corrugated market offers little volume growth, Straub is betting on more efficient production. Plant 3’s first measurable operating results will show whether its new layout and machinery deliver lower costs and more reliable output — the outcome that matters beyond the opening ceremony.
Key sources
SÜDKURIER — Plant 3 opening, 17 October 2026
SÜDKURIER — 2023 groundbreaking, €40–50m estimate excluding machinery
aktiv — Steffen Würth on €50m-plus budget and factory bottlenecks, 15 October 2025
IPPEN.MEDIA — Steffen Würth interview, 16 September 2026
Göpfert — G-CUT 13/21 specifications
VDW — 2025 German corrugated industry results, 21 May 2026
Rondo Ganahl — Frastanz corrugator investment, 26 March 2025
corruga.expert
















